Yamaha QL Series QL 1 Digital Mixer

Giá hãng: 206.000.000 VND

Khuyến mãi:

Bảo hành: 1 năm

QL 1 = 206.000.000

QL 5 = 386.500.000

Hotline: 0908 812 754

QL5QL1
Sampling frequency rateInternal44.1kHz / 48kHz44.1kHz / 48kHz
External44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm)44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm)
Signal delayLess than 2.5ms, INPUT to OMNI OUT, Fs= 48kHzLess than 2.5ms, INPUT to OMNI OUT, Fs= 48kHz
Fader100mm motorized, Resolution=1024steps, +10dB to –138dB, –∞dB all faders100mm motorized, Resolution=1024steps, +10dB to –138dB, –∞dB all faders
Total harmonic distortionLess than 0.05% 20Hz-20kHz@+4dBu into 600Ω, INPUT to OMNI OUT, Input Gain= Min.Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω, INPUT to OMNI OUT, Input Gain= Min.
Frequency response+0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OMNI OUT+0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OMNI OUT
Dynamic range112dB typ.: DA Converter / 108dB typ.: INPUT to OMNI OUT, Input Gain = Min.112dB typ.: DA Converter / 108dB typ.: INPUT to OMNI OUT, Input Gain = Min.
Hum & noise levelEquivalent input noise-128dBu typ., Equivalent Input Noise, Input Gain=Max-128dBu typ., Equivalent Input Noise, Input Gain=Max
Residual output noise-88dBu, Residual output noise, ST master off-88dBu, Residual output noise, ST master off
Crosstalk-100dB*1, adjacent INPUT/OMNI OUT channels, Input Gain = Min.-100dB*1, adjacent INPUT/OMNI OUT channels, Input Gain = Min.
Power requirements100-240V 50/60Hz100-240V 50/60Hz
Power consumption200W135W
DimensionsW828mm(32.6in)468mm(18.4in )
H272mm(10.7in)272mm(10.7in)
D563mm(22.2in)562mm(22.1in)
Net weight21.8kg(48.1lb)14.7kg(32.4lb)
AccessoriesOwner’s Manual, dust cover, power cord, DVS license sheet, Nuendo LiveOwner’s Manual, power cord, DVS license sheet, Nuendo Live
OptionsMini-YGDAI cards *2 , Gooseneck Lamp LA1LRackmount kit RK1, Mini-YGDAI cards *2 , Gooseneck Lamp LA1L
OthersOperating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃

Crosstalk@1kHz : A 22kHz, 30dB/Oct filter is used to measure crosstalk. 
Total Harmonic Distortion : An 80kHz, 18dB/Oct filter is used to measure total harmonic distortion. 
Hum & Noise : An A-Weight filter is used to measure hum &noise.

Analog input characteristics

Input ConnectorsGAINInput 
Impedance
Source 
Impedance
Input levelConnector
Sensitivity*¹NominalMax. before clip
INPUT 
1-32 *6
+66dB7.5 kΩ50-600 Ω 
Mics & 
600 ΩLines
–82dBu 
(61.6μV) 
–62dBu 
(0.616mV) 
–42dBu 
(6.16mV) 
XLR-3-31 
type 
(Balanced) *2
–6dB–10dBu 
(245mV)
+10dBu 
(2.45V)
+30dBu 
(24.5V) 

*1. The sensitivity is the input level required for output at +4dBu (1.23V) or at the defined level when all the faders and level 
controllers are set to the maximum value. 
*2. XLR-3-31 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD). 
*3. 0dBu=0.775 Vrms for all specifications. 
*4. All the AD converters use 24-bit linear/128-times oversampling. 
*5. The INPUT connectors have +48V DC (phantom power) jacks, each of which can be turned on/off individually from the console software. 
*6. QL1: INPUT1-16

Analog output characteristics

Output 
Connectors
Output 
Impedance
Load 
Impedance
Maximum 
Output 
Level *5
Output LevelConnector
Defined LevelMaximum 
Non-Clip Level
OMNI 
OUT 1-16 *7
75 Ω600 Ω 
Lines
+24dB 
(default)
+4dBu 
(1.23V)
vt+24dBu 
(12.3V)
XLR-3-32 type 
(Balanced) *1
+18dB–2dBu 
(616mV)
+18dBu 
(6.16V)
PHONES15 Ω8 Ω 
Phones
-75mW *6150mWStereo Phone 
Jack(TRS) 
(Unbalanced) *2
40 Ω 
Phones
-65mW *6150mW

*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD). 
*2. The PHONES connectors for stereo headphones are balanced jacks (Tip=LEFT, Ring=RIGHT, Sleeve= GND). 
*3. 0 dBu=0.775 Vrms for all specifications. 
*4. All the DA converters use 24-bit linear/128-times oversampling. 
*5. The console has an internal switch for toggling the maximum output level. 
*6. This is a value measured with the PHONES LEVEL knob set to 10 dB below the maximum position. 
*7. QL1: OMNI OUT 1-8

Digital input/output specifications

ConnectorsFormatData lengthLevelAudioConnector
Primary/SecondaryDante24bit or 32bit1000Base-T64ch Input/64ch 
Output@48kHz *1 
EtherCON Cat5e