Yamaha CL Series CL1 Digital Mixer

Giá hãng: 367.000.000 VND

Khuyến mãi:

Bảo hành:

CL1 = 367.000.000

CL3 = 528.000.000
CL5 = 680.000.000

Hotline: 0908 812 754
General specificationsCL5CL3CL1
Sampling frequency rateInternal44.1kHz / 48kHz
External44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm)
Signal delayLess than 2.5ms, OMNI IN to OMNI OUT, Fs=48kHz
Fader100mm motorized, Resolution=1024steps, +10dB to -138dB, -∞dB all faders
Frequency response+0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, OMNI IN to OMNI OUT
Total harmonic distortionLess than 0.05% 20Hz-20kHz@+4dBu into 600Ω, OMNI IN to OMNI OUT, Input Gain = Min.
Hum & Noise-128dBu typ., Equivalent Input Noise, Input Gain=Max., -88dBu, Residual output noise, ST master off
Dynamic range112dB typ.: DA Converter / 108dB typ.: OMNI IN to OMNI OUT, Input Gain = Min.
Crosstalk-100dB*1, adjacent OMNI IN/OMNI OUT channels, Input Gain = Min.
Power requirementsUS/Canada: 120V 60Hz, Japan: 100V 50/60Hz, China: 110-240V 50/60Hz, Korea: 220V 60Hz, Other: 110-240V 50/60Hz
Power consumption170W: Internal Power Supply / 200W: Simultaneous use of Internal PSU and External PW800W
DimensionsW1053mm (41 1/2in)839mm (33 1/8in)648mm (25 5/8in)
H299mm (11 3/4in)299mm (11 3/4in)299mm (11 3/4in)
D667mm (26 1/4in)667mm (26 1/4in)667mm (26 1/4in)
Net weight36kg (79.4lb)29kg (63.9lb)24kg (52.9lb)
OthersTemperature Range: Operating temperature range: 0 - 40°C, Storage temperature range: -20 - 60°C

Analog input characteristics

Input TerminalsGAINActual Load
Impedance
For use with nominalInput levelConnector
Sensitivity*¹NominalMax. before clip
OMNI IN 1-8+66dB7.5kΩ50-600Ω Mics &
600Ω Lines
-82dBu (61.6μV)-62dBu (0.616mV)-42dBu (6.16mV)XLR3-31 type (Balanced)*²
-6dB-10dBu (245mV)+10dBu (2.45V)+30dBu (24.5V)
TALKBACK+64dB10kΩ50-600Ω Mics &
600Ω Lines
-70dBu (0.245mV)
-60dBu (0.775mV)
-40dBu (7.75mV)
XLR3-31 type(Balanced)*²
+20dB-26dBu (38.8mV)-16dBu (0.123V)+4dBu (1.23V)

*1. Sensitivity is the lowest level that will produce an output of +4dBu(1.23V) or the nominal output level when the unit is set to maximum gain.(all faders and level controls are maximum position.)
*2. XLR-3-31 type connectors are balanced..(1=GND, 2=HOT, 3=COLD) 
*3. In these specifications, 0dBu = 0.775 Vrms. 
*4. All input AD converters are 24bit linear, 128times oversampling.
*5. +48V DC ( phantom power ) is supplied to OMNI IN (1-8) and TALKBACK XLR type connectors via each individual software controlled switches.

Analog output characteristics

Output TerminalsActual Source
Impedance
For Use With
Nominal
GAIN SW*5Output LevelConnector
NominalMax. before clip
OMNI OUT 1-875Ω600Ω Lines+24dB (default)+4dBu (1.23 V)
+24dBu (12.3 V)
XLR-3-32 type(Balanced)*1
+18dB-2dBu (616mV)+18dBu (6.16V)
PHONES15Ω8Ω Phones-75mW*6
150mW
Stereo Phone Jack (TRS) (Unbalanced)*2
40Ω Phones-65mW*6150mW

*1. XLR-3-32 type connectors are balanced.( 1=GND, 2=HOT, 3=COLD ) 
*2. PHONES stereo phone jack is unbalanced.( Tip=LEFT, Ring=RIGHT, Sleeve=GND ) 
*3. In these specifications, 0dBu = 0.775 Vrms.
*4. All output DA converters are 24bit, 128times oversampling. 
*5. There are switches inside the body to preset the maximum output level. 
*6. The position of the level control is 10dB lowered from Max.

Digital Input & Output Characteristics

TerminalFormatData lengthLevelAudioConnector
Primary/SecondaryDante24bit or 32bit1000Base-T64ch Input/64ch Output @48kHz
etherCON Cat5e

Digital Output Characteristics

TerminalFormatData lengthLevelConnector
DIGITAL OUTAES/EBUAES/EBU Professional Use24bitRS422
XLR-3-32 type (Balanced)*1